Program windows

Last modified by UT2UK on 2026/11/16 13:22

← EAX control user guide

Program windows

What every EAX button, meter and setting means.

Main window

01_main.png

URL field — the transceiver address and port 4002, for example 192.168.1.50:4002. EAX remembers the addresses it connected to. To remove an address: right-click the field → Delete RIG's URL..

Buttons on the right:

  • ic_connect.png — connect to the transceiver or disconnect. Red means not connected.
  • ic_speaker.png — turn audio on the computer speakers on or off. The arrow next to it selects the receiver.
  • ic_settings.png — settings. Available only when EAX is not connected.

Meters:

  • L — RX1 receiver level;
  • R — RX2 receiver level;
  • M — transmit level: the audio EAX sends to the transceiver.

Status line

The status line shows whether audio is flowing. This is how it looks with a working connection:

1775141576406-233.png

Connected: Speed 730/376 kbit/s, the L and R meters show the receive level.

  • Speed, first number — receive rate: how much audio arrives from the transceiver, in kilobits per second.
  • Speed, second number — transmit rate: how much audio EAX sends to the transceiver.
  • Latency — the computer audio buffer delay, in seconds. It grows when you increase the buffers in settings.

The values are updated every 2 seconds.

What you seeWhat it means
Both numbers above zeroEverything works: audio flows both ways
First number is 0Audio from the transceiver does not arrive. Most often — wrong Local IP address or a firewall. How to fix
First number below 200 and jumpingThe network cannot keep up, the audio will drop out. Check Wi-Fi
Reconnecting in N s...The connection dropped, EAX reconnects by itself in N seconds

If receive stays below 200 kbit/s for about 10 seconds, EAX treats the connection as lost, disconnects and shows Lost connection with Rig.

Listen to the bands on the computer

  1. Connect to the transceiver.
  2. Click ic_speaker.png.
  3. To select a receiver, click the arrow to the right of this button.

02_menu.png

  • RX1+RX2 — both receivers: RX1 in the left ear, RX2 in the right.
  • RX1 — first receiver only, in both ears.
  • RX2 — second receiver only, in both ears.

The choice affects only the speakers. Digital mode programs always get both receivers.

Settings window

Click ic_settings.png, change the parameters and click OK.

03_settings.png

Audio devices

EAX Output — the virtual card for receive. EAX sends the transceiver audio here.

EAX Input — the virtual card for transmit. EAX takes audio from here and sends it to the transceiver.

Audio device — your speakers or headphones.

Which devices to select is shown on the diagrams in the guides for Linux and Windows.

EAX reads the device list at startup. If a device is missing, close EAX and start it again.

RX and TX buffers

The audio reserve size. Auto gives the lowest latency. If the audio drops out — usually on Wi-Fi — select x4 or x8.

Network

Local IP address — the IP address of your computer on the same network as the transceiver. The transceiver sends audio to exactly this address.

This is the most important setting. The first three numbers of the computer and transceiver addresses must match: transceiver 192.168.1.50 → computer 192.168.1.10. On first start it shows 127.0.0.1 — audio does not work with it. Details: why the IP address matters.

Local UDP port — the port the audio arrives on. Leave 16742.

Appearance

Theme — the window colour: System Default, Dark Teal, Dark Amber, Dark Cyan or Light Blue.

04_main_dark_teal.png

Dark Teal theme.

If the connection drops

EAX reconnects by itself: first after a second, then less often, up to once every 30 seconds. The status line shows Reconnecting in N s...

On Windows EAX also works from the tray — see “Working from the tray” in the Windows guide.

Advanced

Where settings are stored
  • Linux: file ~/.config/Ermak/eAX.conf
  • Windows: registry, HKEY_CURRENT_USER\Software\Ermak\eAX
Command-line options and log
eax [options]
  -t, --theme <theme>       default | dark_teal | dark_amber | dark_cyan | light_blue
  -l, --log-file <file>     write the log to a file
  -L, --log-level <level>   error (default) ... debug
  -v, --version             show the version

To report a bug, start EAX with a log and attach the file:

eax -L debug -l ~/eax.log

Related articles