Last modified by UT2UK on 2026/11/16 13:17

Hide last authors
UT2UK 3.3 1 {{velocity}}
UT2UK 3.9 2 $xwiki.ssx.use("Main.DocStyle")$xwiki.jsx.use("Main.DocStyle")
UT2UK 3.3 3 {{/velocity}}
UT2UK 3.2 4
5 (% class="eax" %)
UT2UK 1.1 6 (((
UT2UK 3.2 7 (% class="eax-back" %)
UT2UK 3.11 8 [[← EAX control user guide>>Main.ERMAK-TT.Руководство пользователя EAX control.WebHome]]
UT2UK 1.1 9
UT2UK 3.2 10 (% class="eax-pagehead" %)
11 (((
12 (% class="eax-pagehead-title" %)
UT2UK 3.11 13 JTDX and WSJT-X setup
UT2UK 1.1 14
UT2UK 3.2 15 (% class="eax-pagehead-text" %)
UT2UK 3.11 16 How to set up audio and transceiver control to work FT8, FT4 and other digital modes through EAX. The example is JTDX; WSJT-X uses the same field names.
UT2UK 1.1 17 )))
18
UT2UK 3.11 19 === What you need ===
UT2UK 1.1 20
UT2UK 3.11 21 * EAX is installed and connected to the transceiver: Speed is above zero. Guide for [[Linux>>Main.ERMAK-TT.Руководство пользователя EAX control.Установка и настройка в Linux.WebHome]] or [[Windows>>Main.ERMAK-TT.Руководство пользователя EAX control.Установка и настройка в Windows.WebHome]].
22 * The **RIGCTL** server is enabled on the transceiver and the **EAX** TX source is selected.
23 * JTDX or WSJT-X is installed.
UT2UK 3.2 24
25 (% class="eax-toc" %)
UT2UK 1.1 26 (((
UT2UK 3.11 27 On this page
UT2UK 1.1 28
UT2UK 3.2 29 {{toc depth="2"/}}
UT2UK 1.1 30 )))
31
UT2UK 3.2 32 (% class="eax-howto" %)
33 (((
UT2UK 3.11 34 == Set up audio ==
UT2UK 1.1 35
UT2UK 3.11 36 Open **File → Settings** (key **F2**) and select the **Audio** tab.
UT2UK 1.1 37
UT2UK 3.10 38 (% class="eax-tabs" %)
UT2UK 3.2 39 (((
UT2UK 3.10 40 (% class="eax-tab" %)
UT2UK 3.2 41 (((
42 Linux
UT2UK 1.1 43
UT2UK 3.2 44 * **Input** — **ERMAK_OUT**
45 * **Output** — **ERMAK_IN**
46 )))
UT2UK 1.1 47
UT2UK 3.10 48 (% class="eax-tab" %)
UT2UK 3.2 49 (((
50 Windows
UT2UK 1.1 51
UT2UK 3.2 52 * **Input** — **Line In (EAX VAC)**
53 * **Output** — **Line Volume (2- EAX VAC)**
UT2UK 1.1 54
UT2UK 3.11 55 With Virtual Audio Cable: Input — **Line 1**, Output — **Line 2**.
UT2UK 3.2 56 )))
57 )))
UT2UK 1.1 58
UT2UK 3.11 59 Leave **Mono** for both fields.
UT2UK 3.2 60
61 (% class="eax-shot" %)
62 (((
UT2UK 1.1 63 [[image:jtdx_audio.png]]
UT2UK 3.2 64 )))
UT2UK 1.1 65
UT2UK 3.2 66 (% class="eax-caption" %)
UT2UK 3.11 67 The Audio tab in JTDX, Linux.
UT2UK 1.1 68
UT2UK 3.2 69 (% class="eax-note" %)
UT2UK 1.1 70 (((
UT2UK 3.11 71 The devices in JTDX and in EAX are the two ends of one virtual cable. Do not select in JTDX the same devices as in the EAX Output and EAX Input fields. Diagrams: [[Linux>>Main.ERMAK-TT.Руководство пользователя EAX control.Установка и настройка в Linux.WebHome]], [[Windows>>Main.ERMAK-TT.Руководство пользователя EAX control.Установка и настройка в Windows.WebHome]].
UT2UK 1.1 72 )))
73
UT2UK 3.11 74 == Set up transceiver control ==
UT2UK 1.1 75
UT2UK 3.11 76 Select the **Radio** tab:
UT2UK 3.2 77
78 1. **Rig** — **Hamlib NET rigctl**.
UT2UK 3.11 79 1. **Network Server** — the transceiver IP address and port **4532**, for example **192.168.1.50:4532**. For the second receiver — port **4533**.
UT2UK 3.2 80 1. **PTT Method** — **CAT**.
UT2UK 3.11 81 1. Click **Test CAT** — the button must turn green.
82 1. Click **OK**.
UT2UK 1.1 83
UT2UK 3.2 84 (% class="eax-shot" %)
85 (((
UT2UK 1.1 86 [[image:jtdx_radio.png]]
87 )))
88
UT2UK 3.2 89 (% class="eax-caption" %)
UT2UK 3.11 90 The Radio tab in JTDX.
UT2UK 1.1 91
UT2UK 3.11 92 == Check that it works ==
UT2UK 1.1 93
UT2UK 3.11 94 **Receive.** Turn on the speaker in EAX [[image:Main.ERMAK-TT.Руководство пользователя EAX control.WebHome@ic_speaker.png]] — you should hear the band. Tune to an FT8 segment, for example 14.074 MHz.
UT2UK 1.1 95
UT2UK 3.2 96 (% class="eax-check" %)
97 (((
UT2UK 3.11 98 Check: the level meter in JTDX shows about 30 dB on a quiet band, signals are visible on the waterfall, decodes appear.
UT2UK 3.2 99 )))
UT2UK 1.1 100
UT2UK 3.11 101 **Transmit.** Set low power and click **Tune** in JTDX.
UT2UK 1.1 102
UT2UK 3.2 103 (% class="eax-check" %)
UT2UK 1.1 104 (((
UT2UK 3.11 105 Check: the transceiver goes to transmit, the **M** meter in EAX shows a level, there is output power. Click **Tune** again to stop.
UT2UK 1.1 106 )))
UT2UK 3.2 107 )))
UT2UK 1.1 108
UT2UK 3.11 109 == Recommended settings ==
UT2UK 3.2 110
UT2UK 3.11 111 * Set the receive level with the volume on the transceiver, not with the sliders in Windows.
112 * All virtual cards — 48000 Hz, 16 bit.
113 * Use a separate CAT server for each receiver: RX1 — port 4532, RX2 — port 4533.
114 * If the audio drops out on Wi-Fi, increase **RX buffer** in EAX to x4.
UT2UK 3.2 115
UT2UK 3.11 116 == If it does not work ==
UT2UK 1.1 117
UT2UK 3.11 118 === No signal in JTDX ===
UT2UK 1.1 119
UT2UK 3.11 120 * Do the L and R meters move in EAX? If not, the problem is in EAX, see [[Troubleshooting>>Main.ERMAK-TT.Руководство пользователя EAX control.Решение проблем.WebHome]].
121 * If they move, the wrong **Input** is selected in JTDX. Compare with step 1.
UT2UK 1.1 122
UT2UK 3.11 123 === Test CAT is red ===
UT2UK 3.2 124
UT2UK 3.11 125 * Check the transceiver IP address and port **4532**.
126 * Make sure the RIGCTL server is enabled on the transceiver.
UT2UK 3.2 127
UT2UK 3.11 128 === The transceiver does not transmit or there is no power ===
UT2UK 3.2 129
UT2UK 3.11 130 * The **M** meter in EAX does not move — the wrong **Output** is selected in JTDX.
131 * The meter moves but there is no power — select the **EAX** source on the transceiver in the [[TX settings window>>Main.ERMAK-TT.Руководство пользователя ЕРМАК-ТТ.TX settings.WebHome]].
UT2UK 3.2 132
UT2UK 3.11 133 === Sound card error in JTDX ===
UT2UK 3.2 134
UT2UK 3.11 135 * The device is used by another program or does not exist.
136 * Linux: check that the virtual cards are present — **aplay -l | grep Loopback**.
UT2UK 3.2 137
UT2UK 3.11 138 == Summary of settings ==
UT2UK 3.2 139
UT2UK 3.11 140 |=Tab|=Field|=Linux|=Windows (ERMAK VAC)
UT2UK 3.2 141 |Audio|Input|ERMAK_OUT|Line In (EAX VAC)
142 |Audio|Output|ERMAK_IN|Line Volume (2- EAX VAC)
143 |Radio|Rig|Hamlib NET rigctl|Hamlib NET rigctl
UT2UK 3.11 144 |Radio|Network Server|transceiver IP:4532|transceiver IP:4532
UT2UK 3.2 145 |Radio|PTT Method|CAT|CAT
146
UT2UK 3.11 147 == Related articles ==
UT2UK 3.2 148
UT2UK 3.11 149 * [[Installation and setup on Linux>>Main.ERMAK-TT.Руководство пользователя EAX control.Установка и настройка в Linux.WebHome]]
150 * [[Installation and setup on Windows>>Main.ERMAK-TT.Руководство пользователя EAX control.Установка и настройка в Windows.WebHome]]
151 * [[Troubleshooting>>Main.ERMAK-TT.Руководство пользователя EAX control.Решение проблем.WebHome]]
152 * [[ERMAK-TT TX settings window>>Main.ERMAK-TT.Руководство пользователя ЕРМАК-ТТ.TX settings.WebHome]]
UT2UK 3.2 153 )))