JTDX and WSJT-X setup

Last modified by UT2UK on 2026/11/16 13:17

← EAX control user guide

JTDX and WSJT-X setup

How to set up audio and transceiver control to work FT8, FT4 and other digital modes through EAX. The example is JTDX; WSJT-X uses the same field names.

What you need

  • EAX is installed and connected to the transceiver: Speed is above zero. Guide for Linux or Windows.
  • The RIGCTL server is enabled on the transceiver and the EAX TX source is selected.
  • JTDX or WSJT-X is installed.

Set up audio

Open File → Settings (key F2) and select the Audio tab.

Linux

  • Input — ERMAK_OUT
  • Output — ERMAK_IN

Windows

  • Input — Line In (EAX VAC)
  • Output — Line Volume (2- EAX VAC)

With Virtual Audio Cable: Input — Line 1, Output — Line 2.

Leave Mono for both fields.

jtdx_audio.png

The Audio tab in JTDX, Linux.

The devices in JTDX and in EAX are the two ends of one virtual cable. Do not select in JTDX the same devices as in the EAX Output and EAX Input fields. Diagrams: Linux, Windows.

Set up transceiver control

Select the Radio tab:

  1. Rig — Hamlib NET rigctl.
  2. Network Server — the transceiver IP address and port 4532, for example 192.168.1.50:4532. For the second receiver — port 4533.
  3. PTT Method — CAT.
  4. Click Test CAT — the button must turn green.
  5. Click OK.

jtdx_radio.png

The Radio tab in JTDX.

Check that it works

Receive. Turn on the speaker in EAX ic_speaker.png — you should hear the band. Tune to an FT8 segment, for example 14.074 MHz.

Check: the level meter in JTDX shows about 30 dB on a quiet band, signals are visible on the waterfall, decodes appear.

Transmit. Set low power and click Tune in JTDX.

Check: the transceiver goes to transmit, the M meter in EAX shows a level, there is output power. Click Tune again to stop.

Recommended settings

  • Set the receive level with the volume on the transceiver, not with the sliders in Windows.
  • All virtual cards — 48000 Hz, 16 bit.
  • Use a separate CAT server for each receiver: RX1 — port 4532, RX2 — port 4533.
  • If the audio drops out on Wi-Fi, increase RX buffer in EAX to x4.

If it does not work

No signal in JTDX

  • Do the L and R meters move in EAX? If not, the problem is in EAX, see Troubleshooting.
  • If they move, the wrong Input is selected in JTDX. Compare with step 1.

Test CAT is red

  • Check the transceiver IP address and port 4532.
  • Make sure the RIGCTL server is enabled on the transceiver.

The transceiver does not transmit or there is no power

  • The M meter in EAX does not move — the wrong Output is selected in JTDX.
  • The meter moves but there is no power — select the EAX source on the transceiver in the TX settings window.

Sound card error in JTDX

  • The device is used by another program or does not exist.
  • Linux: check that the virtual cards are present — aplay -l | grep Loopback.

Summary of settings

TabFieldLinuxWindows (ERMAK VAC)
AudioInputERMAK_OUTLine In (EAX VAC)
AudioOutputERMAK_INLine Volume (2- EAX VAC)
RadioRigHamlib NET rigctlHamlib NET rigctl
RadioNetwork Servertransceiver IP:4532transceiver IP:4532
RadioPTT MethodCATCAT

Related articles